Overview
W6100-EVB is an evaluation board for W6100 chip based on the 32-bit ARM® Cortex™-M3 microcontroller. It is the easy way to develop internet connection for efficient and small embedded systems using W6100, WIZnet’s hardwired TCP/IP embedded Ethernet controller. It has been designed to be hardware pin-compatible with ‘Arduino shields’ for the ‘Arduino UNO Rev3’ and other footprint-compatible boards.
It is based on the STM STM32F103VCT6 MCU with a 32-bit ARM® Cortex™-M3 core running at Maximum 72MHz. It includes 256 or 512kB Flash memory, 64kB SRAM various interfaces, including BUS(Flexible static memory controller), SPI/SSP, I2C, UART, ADC, PWM, and other I/O interfaces. Additionally, Two programmable pushbutton switches, one RGB LED and a 10/100 Base-Tx RJ-45 connector with an integrated transformer is on board to implement embedded networking applications.
The W6100-EVB provides benefits in developing easier and powerful network applications on small form-factor and non-OS based embedded devices using the W6100 chip.
Features
WIZnet W6100 Hardwired TCP/IP chip
-
Hardwired TCP/IP embedded Ethernet controller
-
Parallel Host Interface (External BUS Interface)
-
SPI (Serial Peripheral Interface) Microcontroller Interface
-
32kB internal Tx/Rx socket buffer memory (8 sockets)
-
Support SOCKET-less Command: ARP-Request, PING-Request
-
Support Auto-Negotiation (Full/Half Duplex, 10/100 Speed)
-
Support Auto-MDIX when Auto-Negotiation Mode.
-
Hardwired TCP/IP stack supports TCP, UDP, IPv6, IPv4, ICMPv6, ICMPv4, IGMP, MLDv1, ARP, PPPoE protocols
STMicroelectronics STM32F103VCT6 MCU
-
32-bit ARM® Cortex™-M3 microcontroller running at up to 75MHz
-
256 Kbytes of Flash memory
-
48 Kbytes of SRAM
-
5 × USARTs
-
4 × 16-bit timers, 2 × basic timers
-
3 × SPIs, 2 × I2Ss, 2 × I2Cs
-
USB, CAN, 2 × PWM timers
-
3 × ADCs, 2 × DACs, 1 × SDIO
-
FSMC (100- and 144-pin packages)
Connectors
-
1-Channel 10/100Mbps Ethernet Connector (RJ45 with transformer)
-
Virtual COM Port(UART via Micro USB B type) –
CP2104 Drivers Download Page
-
Expansion 80 GPIOs (Include analog Peripheral using 12bit ADC)
-
Pin-compatible with Arduino Shields designed for the UNO Rev3
-
Digital pins D0 to D15, Analog inputs A0 to A5, the power header and Etc.
-
ARM standard debug connector: 5-pin Cortex debug connector for SWD (Serial Wire Debug)
Others
-
2 x User’s Push-button switches
-
1 x RGB LED
-
Industrial temperature specified (-40 to +85 degrees Celsius)
-
[Reset] and [boot0] ISP access push button switch
Form-factor
-
Dimension : 90 X 80 X 15(H) (Unit : mm)
-
5V DC power supply
-
GPIO Input Voltage : 0 ~ 5V
-
GPIO Output Voltage : 0 ~ 3.3V
-
4-layer PCB (FR-4 material, 1.6T, 1oz)
-
Arduino Compatible with SWD Header Pinout
-
External Pinout (left side)
-
External Pinout (Right side)
Firmware
W6100-EVB firmware project based on Eclipse IDE. For more details about Eclipse IDE, please refer to below link.
Download the Libraries and Application example source code for W6100-EVB
https://github.com/Wiznet/W6100_EVB
Getting Started
Make New EVB Projects
It is the same as W5100-EVB
Make New EVB Projects using Eclipse
Make New EVB Projects using TrueSTUDIO
Technical Reference
Datasheet
Schematic & Part list
Dimension
-
W6100-EVB Rev1.1 Dimension(unit:mm)
Be the first to review “W6100-EVB”